Hoshizaki America, Inc.
Hoshizaki
Cubelet Icemaker/Dispenser
Models
DCM-300BAH(-OS)
INSTRUCTION MANUAL
“A Superior Degree
of Reliability”
Issued: 3-2-2011
Revised: 2-13-2015
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
This manual should be read carefully before the icemaker is installed and
operated. Only qualified service technicians should install, service, and
maintain the icemaker. Read the warnings contained in this booklet carefully as
they give important information regarding safety. Please retain this booklet for
any further reference that may be necessary.
CONTENTS
Important Safety Information ................................................................................................. 4
I. Specifications...................................................................................................................... 5
A. Electrical Data............................................................................................................... 5
1. DCM-300BAH .......................................................................................................... 5
2. DCM-300BAH-OS ................................................................................................... 6
B. Dimensions/Connections .............................................................................................. 7
1. DCM-300BAH .......................................................................................................... 7
2. DCM-300BAH-OS ................................................................................................... 8
II. Installation and Operating Instructions .............................................................................. 9
A. Checks Before Installation............................................................................................. 9
B. How to Remove Panels............................................................................................... 10
C. Location .......................................................................................................................11
D. Setup............................................................................................................................11
E. Electrical Connection .................................................................................................. 12
F. Water Supply and Drain Connections .......................................................................... 13
G. Final Checklist ............................................................................................................ 15
H. Startup ........................................................................................................................ 16
I. Dispense Mode Switch................................................................................................. 17
III. Cleaning and Maintenance............................................................................................. 18
A. Cleaning and Sanitizing Instructions........................................................................... 19
1. Water System......................................................................................................... 19
2. Dispensing Components ....................................................................................... 21
B. Maintenance................................................................................................................ 23
C. Preparing the Icemaker for Long Storage ................................................................... 24
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
Throughout this manual, notices appear to bring your attention to situations which could
result in death, serious injury, or damage to the unit.
WARNING
Indicates a hazardous situation which could result in death or
serious injury.
CAUTION
IMPORTANT
Indicates a situation which could result in damage to the unit.
Indicates important information about the use and care of the
unit.
WARNING
This icemaker should be destined only to the use for which it has been
expressly conceived. Any other use should be considered improper and
therefore dangerous. The manufacturer cannot be held responsible for injury or
damage resulting from improper, incorrect, and unreasonable use.
To reduce the risk of death, electric shock, serious injury, or fire, follow
basic precautions including the following:
• Only qualified service technicians should install, service, and maintain the
icemaker.
• Electrical connection must be hard-wired and must meet national, state, and
local electrical code requirements. Failure to meet these code requirements
could result in death, electric shock, serious injury, fire, or severe damage to
equipment.
• This unit requires an independent power supply. See the nameplate for
proper voltage and breaker/fuse size. Failure to use a proper breaker or fuse
can result in a tripped breaker, blown fuse, or damage to existing wiring. This
could lead to heat generation or fire.
• THIS UNIT MUST BE GROUNDED. Failure to properly ground this unit could
result in death or serious injury.
• Move the control switch and the power switch to the "OFF" position and turn
off the power supply before servicing. Lockout/Tagout to prevent the power
supply from being turned back on inadvertently.
• Do not make any alterations to the unit. Alterations could result in electric
shock, injury, fire, or damage to the unit.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
I. Specifications
A. Electrical Data
1. DCM-300BAH
MODEL NUMBER
DCM-300BAH
SERIAL NUMBER
AC SUPPLY VOLTAGE
COMPRESSOR
GEAR MOTOR
FAN MOTOR
AGITATING MOTOR
DISPENSING MOTOR
OTHER
115-120/60/1
120V 7.9RLA 39.0RLA
120V 1.45FLA 80W
115V 0.8FLA 16W
120V 0.9FLA 55W
120V 0.9FLA 55W
120V 0.2A
MAXIMUM FUSE SIZE
MAX. HACR BREAKER (USA ONLY)
MAX. CIRC. BREAKER (CANADA ONLY)
MINIMUM CIRCUIT AMPACITY
DESIGN PRESSURE
REFRIGERANT
20 AMPS
20 AMPS
20 AMPS
20 AMPS
HI-460PSI LO-290PSI
404A 15.9 OZ.
MOTOR-COMPRESSOR THERMALLY PROTECTED
NOT INTENDED FOR OUTDOOR USE!
Hoshizaki America, Inc.
Peachtree City, GA
For certification marks, see the nameplate
on the rear panel.
The rating label and nameplate provide electrical and refrigerant data. The rating label can
be seen by removing the front panel. The nameplate is located on the rear panel.
We reserve the right to make changes in specifications and design without prior notice.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. DCM-300BAH-OS
MODEL NUMBER
DCM-300BAH-OS
SERIAL NUMBER
AC SUPPLY VOLTAGE
COMPRESSOR
GEAR MOTOR
FAN MOTOR
AGITATING MOTOR
DISPENSING MOTOR
OTHER
115-120/60/1
120V 7.9RLA 39.0LRA
120V 1.45FLA 80W
115V 0.8FLA 16W
120V 0.9FLA 55W
120V 0.9FLA 55W
120V 0.2A
MAXIMUM FUSE SIZE
MAX. HACR BREAKER (USA ONLY)
MAX. CIRC. BREAKER (CANADA ONLY)
MINIMUM CIRCUIT AMPACITY
DESIGN PRESSURE
REFRIGERANT
20 AMPS
20 AMPS
20 AMPS
20 AMPS
HI-460PSI LO-290PSI
404A 15.9 OZ.
MOTOR-COMPRESSOR THERMALLY PROTECTED
NOT INTENDED FOR OUTDOOR USE!
Hoshizaki America, Inc.
Peachtree City, GA
For certification marks, see the nameplate
on the rear panel.
The rating label and nameplate provide electrical and refrigerant data. The rating label can
be seen by removing the front panel. The nameplate is located on the rear panel.
We reserve the right to make changes in specifications and design without prior notice.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Dimensions/Connections
1. DCM-300BAH
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2. DCM-300BAH-OS
8
Download from Www.Somanuals.com. All Manuals Search And Download.
II. Installation and Operating Instructions
WARNING
1. This icemaker must be installed in accordance with applicable national, state,
and local codes and regulations.
2. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews
are securely in place after installation. Make sure that none have fallen into
the storage bin.
A. Checks Before Installation
• Visually inspect the exterior of the shipping container and immediately report any
damage to the carrier. Upon opening the container, any concealed damage should also
be immediately reported to the carrier.
• Remove the shipping carton, tape, and packing material. If any are left in the icemaker,
it will not work properly.
• Remove the panels to prevent damage when installing the icemaker. See "II.B. How to
Remove Panels."
• Remove the package containing the accessories.
• Remove the protective plastic film from the panels. If the icemaker is exposed to the
sun or to heat, remove the film after the icemaker cools.
• Check that the refrigerant lines do not rub or touch lines or other surfaces, and that the
fan blade (if applicable) turns freely.
• Check that the compressor is snug on all mounting pads.
• See the nameplate on the rear panel, and check that your voltage supplied
corresponds with the voltage specified on the nameplate.
• This icemaker can be installed on a countertop or on an optional stand. If using an
optional stand, Hoshizaki Stand SD-450 or SD-500 is recommended. For further
options, contact your local Hoshizaki distributor.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
B. How to Remove Panels
See Fig. 1 or Fig. 2
• Front Panel: Remove the screw. Lift up and towards you. Disconnect the connector on
push-button models.
• Top Panel: Lift up at front slightly, push rearward and lift off.
• Apron Panel: Remove the screws and pull towards you. Disconnect the connectors on
Opti-Serve models.
• Side Panels: Remove the screws and pull towards you.
• Storage Bin Cover: Remove the thumbscrews and pull towards you.
DCM-300BAH
(Push-Button Models)
Top Panel
Storage Bin
Cover
Side Panel
Side Panel
Front Panel
Connector
Apron Panel
Fig. 1
DCM-300BAH-OS
(Opti-Serve Models)
Top Panel
Side Panel
Storage Bin
Cover
Side Panel
Connectors
Front Panel
Apron Panel
Fig. 2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Location
CAUTION
1. This icemaker is not intended for outdoor use. Normal operating ambient
temperature should be within 45°F to 100°F (7°C to 38°C); Normal operating
water temperature should be within 45°F to 90°F (7°C to 32°C). Operation
of the icemaker, for extended periods, outside of these normal temperature
ranges may affect icemaker performance.
2. This icemaker will not work at sub-freezing temperatures. To prevent
damage to the water supply line, drain the icemaker if the air temperature is
going to go below 32°F (0°C). See "III.C. Preparing the Icemaker for Long
Storage."
IMPORTANT
Opti-Serve Models (-OS): Sunlight, direct and indirect, can have an effect on
the operation of the dispense sensors. If a problem is noticed, the icemaker
should be moved out of direct sunlight and/or farther away from any outside
windows.
For best operating results:
• The icemaker should not be located next to ovens, grills, or other high heat producing
equipment.
• The location should provide a firm and level foundation for the equipment.
• Allow 6" (15 cm) clearance at rear and sides for proper air circulation and ease of
maintenance and/or service should they be required. Allow 24" (61 cm) clearance at top
to allow for removal of the auger.
D. Setup
1) Position the icemaker in the selected permanent location. If applicable, attach optional
6" legs or attach to an optional stand. If attaching to a stand, refer to the instructions
included with the stand.
2) Level the icemaker in both the left-to-right and front-to-rear directions. If using optional
6" legs or an optional stand, adjust the legs to make the icemaker level.
3) If mounting flat to a counter, seal the perimeter where the icemaker contacts the
counter with approved caulk compound in a smooth and easily cleanable manner.
4) Replace the panels in their correct positions.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Electrical Connection
WARNING
1. Electrical connection must be hard-wired and must meet national, state, and
local electrical code requirements. Failure to meet these code requirements
could result in death, electric shock, serious injury, fire, or extensive damage
to equipment.
2. This unit requires an independent power supply. See the nameplate for proper
voltage and breaker/fuse size. Failure to use a proper breaker or fuse can
result in a tripped breaker, blown fuses, or damage to existing wiring. This
could lead to heat generation or fire.
3. THIS UNIT MUST BE GROUNDED. Failure to properly ground this unit could
result in death or serious injury.
4. Electrical connection must be made in accordance with the instructions on
the "WARNING" tag, provided with the pig tail leads in the junction box. See
Fig. 3.
• Usually an electrical permit and services of a licensed electrician are required.
• The maximum allowable voltage variation is 10 percent of the nameplate rating.
• The white lead must be connected to the neutral conductor of the power source.
CAUTION! Miswiring may result in severe damage to the icemaker. See Fig. 3.
• The opening for the power supply connection is 7/8" DIA to fit a 1/2" trade size conduit.
ꢀWARNING
ELECTRICAL CONNECTION
THISꢀUNITꢀMUSTꢀBEꢀGROUNDED
Failure to properly ground or wire
this unit could result in death,
serious injury, or severe damage
to the icemaker. The white lead
must be connected to the neutral
conductor of the power source.
See diagram below.
115-120/60/1
JUNCTIONꢀBOX
L
BROWN
N
WHITE
Fig. 3
12
Download from Www.Somanuals.com. All Manuals Search And Download.
F. Water Supply and Drain Connections
See Fig. 4.
WARNING
1. Water supply and drain connections must be installed in accordance with
applicable national, state, and local codes and regulations.
2. Normal operating water temperature should be within 45°F to 90°F (7°C
to 32°C). Operation of the icemaker, for extended periods, outside of this
normal temperature range may affect icemaker performance.
3. To prevent damage to equipment, do not operate the icemaker when the
water supply is off, or if the pressure is below 10 PSIG. Do not run the
icemaker until the proper water pressure is reached.
• A plumbing permit and services of a licensed plumber may be required in some areas.
• External filters, strainers, or softeners may be required depending on water quality. Contact
your local Hoshizaki distributor for recommendations.
• Water supply pressure should be a minimum of 10 PSIG and a maximum of 113 PSIG. If
the pressure exceeds 113 PSIG, the use of a pressure reducing valve is required.
• The storage bin drain line and drip tray drain line must be run separately.
• Drain lines must have 1/4" fall per foot (2 cm per 1 m) on horizontal runs to get a good
flow. A vented tee connection is also required for proper flow.
• Drain lines should not be piped directly to the sewer system. An air gap of a minimum of
2 vertical inches (5 cm) should be between the end of the drain pipes from the storage bin
and drip tray and the floor drain.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Icemaker
• Icemaker water supply inlet is 1/2" female pipe thread (FPT). A minimum of 1/4" nominal
ID copper water tubing or equivalent is required for the icemaker water supply line.
• An icemaker water supply line shut-off valve and drain valve should be installed.
• Storage bin and drip tray drain outlets are 3/4" FPT. A minimum of 3/4" nominal ID hard
pipe or equivalent is required for the storage bin and drip tray drain lines.
Icemaker
Icemaker Water Supply
Line Shut-Off Valve
Icemaker Water
Supply Inlet
1/2" FPT
Minimum 1/4"
Nominal ID Copper
Water Tubing
Drip Tray
Drain Outlet
3/4" FPT
Vent
Tube
Icemaker Water Supply
Line Drain Valve
Storage Bin
Drain Outlet
3/4" FPT
Stand
Separate piping to approved
drain. Leave a 2-inch (5-cm)
vertical air gap between the
end of each pipe and the
drain.
2-inch (5-cm)
air gap
Minimum 3/4" Nominal ID
Hard Pipe
DCM-300BAH(-OS)
Floor
Drain
Fig. 4
14
Download from Www.Somanuals.com. All Manuals Search And Download.
G. Final Checklist
WARNING
CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are
securely in place after installation. Make sure that none have fallen into the
storage bin.
1) Is the icemaker level?
2) Is the icemaker in a site where the ambient temperature is within 45°F to 100°F (7°C to
38°C) and the water temperature within 45°F to 90°F (7°C to 32°C) all year around?
3) Is there at least 6" (15 cm) clearance at rear and sides and 24" (61 cm) at top for proper
air circulation and ease of maintenance and service?
4) Have the shipping carton, tape, and packing material been removed from the icemaker?
5) If the icemaker is mounted flat to a counter, has the perimeter where the icemaker
contacts the counter been sealed with approved caulk compound? If the icemaker is on
a stand, has it been secured to the stand as outlined in the stand's instructions?
6) Have all electrical and water connections been made? Do electrical and water
connections meet all national, state, and local code and regulation requirements?
7) Has the power supply voltage been checked or tested against the nameplate rating?
Has a proper ground been installed to the icemaker?
8) Are the water supply line shut-off valve and drain valve installed? Has the water supply
pressure been checked to ensure a minimum of 10 PSIG and a maximum of 113 PSIG?
Note: The icemaker may stop running when the water supply is off, or if the pressure
is below 10 PSIG. When the proper water pressure is reached, the icemaker
automatically starts running again.
9) Are the compressor hold-down bolts snug? Have the refrigerant lines been checked
to make sure they do not rub or touch other lines or surfaces? Has the fan blade been
checked to make sure it turns freely?
10) Are all components, fasteners, and thumbscrews securely in place?
11) Has the end user been given the instruction manual, and instructed on how to operate
the icemaker and the importance of the recommended periodic maintenance?
12) Has the end user been given the name and telephone number of an authorized service
agent?
13) Has the warranty card been filled out and forwarded to the factory for warranty
registration?
15
Download from Www.Somanuals.com. All Manuals Search And Download.
H. Startup
WARNING
1. All parts are factory-adjusted. Improper adjustments may adversely affect
safety, performance, component life, and warranty coverage.
2. If the icemaker is turned off, wait for at least 3 minutes before restarting the
icemaker to prevent damage to the compressor.
3. At startup, confirm that all internal and external connections are free of leaks.
1) Open the water supply line shut-off valve.
2) Remove the front panel. Move the control switch to the "OFF" position, then move the
power switch to the "ON" position. See Fig. 5. Replace the front panel in its correct
position, then turn on the power supply. Note: This unit will not run if the safety switch is
not engaged.
3) Move the control switch to the "ICE" position to start the automatic icemaking process.
4) Once the unit starts to produce ice, allow it to run for another 30 minutes.
5) Move the control switch to the "DRAIN" position. Allow the water system to drain for
5 minutes. Note: If the unit is running, the drain valve will not open until 2.5 minutes
after the control switch is moved to the "DRAIN" position. This allows the components to
cycle down.
6) Move the dispense mode switch to the "CONTINUOUS" position, then dispense all
of the ice from the storage bin. Note: Ice dispenses continuously for a maximum of
60 seconds per activation.
7) Remove the front panel, then remove the storage bin cover. See Fig. 5.
8) To confirm bin control operation, move the control switch to the "ICE" position, then
engage the safety switch on the front frame. Allow the unit to run until the compressor
starts (approximately 60 seconds). Press and hold the actuator paddle located inside
the storage bin. WARNING! Keep hands, hair, and loose clothing clear of the
agitator inside the storage bin. The compressor should de-energize 90 seconds later,
and the gear motor should de-energize 60 seconds after that.
Actuator Paddle
Storage Bin Cover
Power Switch
Safety Switch
Control Switch
Dispense Mode Switch
Fig. 5
16
Download from Www.Somanuals.com. All Manuals Search And Download.
9) Disengage the safety switch. Move the control switch to the "OFF" position, then move
the power switch to the "OFF" position. Turn off the power supply.
10) Clean the storage bin liner, cover, and components using a neutral cleaner. Rinse
thoroughly after cleaning. Replace the storage bin cover in its correct position.
WARNING! CHOKING HAZARD: Ensure all components, fasteners, and
thumbscrews are securely in place. Make sure that none have fallen into the
storage bin.
11) Move the power switch to the "ON" position, then replace the front panel in its correct
position. Turn on the power supply, then move the control switch to the "ICE" position to
start the automatic icemaking process.
I. Dispense Mode Switch
The dispense mode switch has "CONTINUOUS" and "PORTION" positions.
When the dispense mode switch is in the "CONTINUOUS" position, ice dispenses
continuously for a maximum of 60 seconds per activation.
When the dispense mode switch is in the "PORTION" position, ice dispenses for the
amount of time determined by the ice dispense time setting. The ice dispense time
control is located on the control board. The dial indicates dispense time in seconds.
See Fig. 6. When shipped, the ice dispense time control is set to the minimum
dispense time of 0.6 sec. At this setting, approximately 0.72 oz. of ice is dispensed. The
DCM-300BAH(-OS) dispenses approximately 1.2 oz. of ice per second.
Fig. 6
17
Download from Www.Somanuals.com. All Manuals Search And Download.
III. Cleaning and Maintenance
This icemaker must be cleaned and maintained in accordance with the instruction
manual and labels provided with the icemaker. Consult with your local distributor
about cleaning and maintenance service. To obtain the name and phone number of
1-800-233-1940 in the USA.
WARNING
1. Only qualified service technicians should service this icemaker.
2. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews
are securely in place after any cleaning or maintenance is done to the unit.
Make sure that none have fallen into the storage bin.
3. The storage bin is for ice use only. Do not store anything else in the storage
bin.
Spout A
Spout B
Extruding Head
Reservoir
Bin Control Assembly
Agitator
Power Switch
Float Switch
Assembly
Dispensing
Auger
Evaporator Assembly
Agitating Motor
Dispensing Motor
Storage Bin Cover
4A1038-014
CONTROL
ICE
OFF
DISPENSE MODE
Spout Cover
PORTION
DRAIN
CONTINUOUS
Safety Switch
Optical Sensors (-OS model)
Fig. 7
18
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Cleaning and Sanitizing Instructions
Hoshizaki recommends cleaning and sanitizing this unit at least twice a year. More
frequent cleaning and sanitizing, however, may be required in some existing water
conditions.
WARNING
1. To prevent injury to individuals and damage to the icemaker, do not use
ammonia type cleaners.
2. Carefully follow any instructions provided with the bottles of cleaning and
sanitizing solution.
3. Always wear liquid-proof gloves and goggles to prevent the cleaning and
sanitizing solutions from coming into contact with skin or eyes.
4. Do not use ice made from the cleaning and sanitizing solutions. After cleaning
and sanitizing, be careful not to leave any solution on the parts or in the
storage bin.
1. Water System
a) Cleaning Solution
Dilute 9.6 fl. oz. (0.29 l) of Hoshizaki "Scale Away" with 1.6 gal. (6.0 l) of warm water.
b) Cleaning Procedure
1) Close the icemaker water supply line shut-off valve.
2) Move the control switch to the "DRAIN" position. See Fig. 7. Allow the water system to
drain for 5 minutes.
3) Move the dispense mode switch to the "CONTINUOUS" position, then dispense all of
the ice from the storage bin.
Note: Ice dispenses continuously for a maximum of 60 seconds per activation.
4) Move the control switch to the "OFF" position, then turn off the power supply. Remove
the front and top panels, then move the power switch to the "OFF" position.
5) Remove the storage bin cover. Remove spout B, then remove spout A.
6) Pour the cleaning solution over the extruding head until the evaporator assembly and
the reservoir are full and the solution starts to overflow into the drain pan.
Note: If there is excess scale on the extruding head, fill the evaporator assembly and
reservoir as described above, then use a clamp on the reservoir hose between
the reservoir and evaporator assembly to block flow. Pour additional cleaning
solution over the extruding head until the evaporator assembly is completely full.
7) Replace spout A, spout B, and the storage bin cover in their correct positions.
8) Allow the icemaker to sit for 10 minutes before operation. If you placed a clamp on the
reservoir hose in step 6, remove it before operation.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
9) In bad or severe water conditions, clean the float switch assembly as described below.
Otherwise, continue to step 10.
a. Remove the float switch assembly from the reservoir cover.
b. Wipe down the float switch assembly with the cleaning solution.
c. Rinse the float switch assembly thoroughly with clean water.
d. Replace the float switch assembly in its correct position.
10) Move the power switch to the "ON" position and replace the panels in their correct
positions. Turn on the power supply, then move the control switch to the "ICE" position.
Make ice using the solution until the icemaker stops making ice.
Note: This unit will not run if the safety switch is not engaged.
11) Move the control switch to the "DRAIN" position. Allow the water system to drain for
5 minutes.
12) Move the control switch to the "ICE" position. Open the icemaker water supply line
shut-off valve to supply water to the reservoir.
13) After the gear motor starts, move the control switch to the "DRAIN" position. Allow the
water system to drain for 5 minutes.
Note: If you do not sanitize the unit, move the control switch to the "ICE" position after
the water system drains. Allow the icemaker to run for 30 minutes, then move the
control switch to the "OFF" position. Turn off the power supply, then remove the
front panel and storage bin cover. Move the power switch to the "OFF" position.
Go to step 12 in "III.A.2.c) Cleaning and Sanitizing Procedure" under "Dispensing
Components."
14) Move the control switch to the "OFF" position, then turn off the power supply.
15) Close the icemaker water supply line shut-off valve.
c) Sanitizing Solution
Dilute 0.82 fl. oz. (25 ml) of a 5.25% sodium hypochlorite solution (chlorine bleach) with
1.6 gal. (6.0 l) of warm water.
d) Sanitizing Procedure - Following Cleaning Procedure
1) Make sure the control switch is in the "OFF" position, the power supply is off, and the
icemaker water supply line shut-off valve is closed.
2) Remove the front and top panels, then move the power switch to the "OFF" position.
3) Remove the storage bin cover. Remove spout B, then remove spout A.
4) Pour the sanitizing solution over the extruding head until the evaporator assembly and
the reservoir are full and the solution starts to overflow into the drain pan.
5) Replace spout A, spout B, and the storage bin cover in their correct positions.
6) Allow the icemaker to sit for 10 minutes before operation.
7) Move the power switch to the "ON" position and replace the panels in their correct
positions. Turn on the power supply, then move the control switch to the "ICE" position.
Make ice using the solution until the icemaker stops making ice.
8) Move the control switch to the "DRAIN" position. Allow the water system to drain for
5 minutes.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
9) Move the control switch to the "ICE" position. Open the icemaker water supply line
shut-off valve to supply water to the reservoir.
10) After the gear motor starts, move the control switch to the "DRAIN" position. Allow the
water system to drain for 5 minutes.
11) Move the control switch to the "ICE" position. Allow the icemaker to run for 30 minutes,
then clean and sanitize the dispensing components as outlined below.
2. Dispensing Components
Perform after cleaning and sanitizing the water system as outlined above.
a) Cleaning Solution
Dilute 9.6 fl. oz. (0.29 l) of Hoshizaki "Scale Away" with 1.6 gal. (6.0 l) of warm water.
b) Sanitizing Solution
Dilute 0.82 fl. oz. (25 ml) of a 5.25% sodium hypochlorite solution (chlorine bleach) with
1.6 gal. (6.0 l) of warm water.
c) Cleaning and Sanitizing Procedure
1) Move the control switch to the "OFF" position, then turn off the power supply.
2) Remove the front and top panels, then move the power switch to the "OFF" position.
3) Remove the storage bin cover.
4) Remove the motor bracket thumbscrews, first from the vertical plane and then from
the horizontal plane. While holding on to the corresponding agitator or auger, move
the agitating motor or the dispensing motor towards you. Remove the agitator and the
dispensing auger from the storage bin. See Fig. 7.
5) Remove the bin control assembly. See Fig. 8.
6) Remove the snap pin, shaft, and actuator.
7) Remove spout B, spout A, and their gaskets.
Spout B
Spout A
Bin Control
Bracket
Snap Pin
Shaft
Fig. 8
Actuator
21
Download from Www.Somanuals.com. All Manuals Search And Download.
8) Remove the spout cover, ice dispensing spout, and water dispensing nozzle. See Fig. 9.
9) Immerse the agitator, dispensing auger, and parts removed in steps 5 through 8 in the
cleaning solution and then in the sanitizing solution for 15 minutes each. Rinse the parts
thoroughly with clean water. On Opti-Serve models (-OS), wipe the optical sensors with
cleaning solution and then with a clean, damp cloth.
10) Wipe the shutter located above the ice dispensing spout thoroughly with a clean cloth.
11) Reassemble the bin control assembly and replace all parts in the reverse order of which
they were removed.
12) Pour warm water into the storage bin and melt any remaining ice. Clean the storage bin
liner and the storage bin cover using a neutral cleaner. Rinse thoroughly after cleaning.
Replace the storage bin cover in its correct position.
13) Move the power switch to the "ON" position, then replace the panels in their correct
positions. Turn on the power supply, then move the control switch to the "ICE" position
to start the automatic icemaking process.
Water Dispensing Nozzle
Ice Dispensing Spout
Spout Cover
Fig. 9
22
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Maintenance
The maintenance schedule below is a guideline. More frequent maintenance may be
required depending on water quality, the icemaker's environment, and local sanitation
regulations.
WARNING
1. Only qualified service technicians should service this icemaker.
2. Move the control switch and the power switch to the "OFF" position and turn
off the power supply before servicing. Lockout/Tagout to prevent the power
supply from being turned back on inadvertently.
Maintenance Schedule
Frequency Area
Task
Every 2
Weeks
Air Filter
Inspect. Wash with warm water and neutral cleaner if dirty.
Monthly
External Water
Filters
Check for proper pressure and change if necessary.
Icemaker Exterior Wipe down with a clean, soft cloth. Use a damp cloth containing a neutral
cleaner to wipe off oil or dirt build up. Clean any chlorine staining (rust
colored spots) using a non-abrasive cleaner like Zud or Bon Ami.
Every 6
Months
Icemaker and
Storage Bin
Clean and sanitize per the cleaning and sanitizing instructions provided in
this manual.
Evaporator
Wipe down with a clean cloth and warm water. Slowly pour one cup of
Condensate Drain sanitizing solution (prepare as outlined in the sanitizing instructions in
Pan and Gear
Motor Drain Pan
this manual) into the evaporator condensate drain pan. Be careful not to
overflow the pan. This solution will flow down to the gear motor drain pan
and out the drain line to sanitize these areas. Repeat with a cup of clean
water to rinse.
Icemaker, Storage Check to make sure they are clear.
Bin, and Drip Tray
Drains
Yearly
Inlet Water Valve
and Drain Valve
Close the icemaker water supply line shut-off valve and drain the water
system. Clean the inlet water valve screen and clean and inspect the drain
valve.
Water Hoses
Condenser
Icemaker
Inspect the water hoses and clean/replace if necessary.
Inspect. Clean if necessary by using a brush or vacuum cleaner.
Inspect for oil spots, loose components, fasteners, and wires.
Upper Bearing
(extruding head)
Check for wear using .02" round stock or pin gauge. Replace both upper
bearing and lower bearing if wear exceeds factory recommendations. See
the Service Manual for details.
After
3 Years,
then Yearly Lower Bearing
and O-Ring
Upper Bearing
(extruding head);
Inspect. Replace both upper bearing and lower bearing if wear exceeds
factory recommendations. Replace the mechanical seal if the seal's contact
surfaces are worn, cracked, or scratched.
(lower housing);
Mechanical
Seal; Evaporator
Cylinder; Auger
23
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Preparing the Icemaker for Long Storage
CAUTION
When storing the icemaker for an extended time or in sub-freezing
temperatures, follow the instructions below to prevent damage.
When the icemaker is not used for two or three days under normal conditions,
it is sufficient to only move the control switch to the "OFF" position. When
storing the icemaker for extended time or in sub-freezing temperatures, follow
the instructions below.
1. Remove the ice from the storage bin, drain the water system, and remove the
water from the icemaker water supply line:
1) Close the icemaker water supply line shut-off valve and open the icemaker water
supply line drain valve.
2) Move the control switch to the "DRAIN" position. Allow the water system to drain for
5 minutes.
3) Move the dispense mode switch to the "CONTINUOUS" position, then dispense all of
the ice from the storage bin.
Note: Ice dispenses continuously for a maximum of 60 seconds per activation.
4) Attach a compressed air or carbon dioxide supply to the icemaker water supply line
drain valve.
5) While engaging the water dispense switch, blow out the water dispense valve using the
compressed air or carbon dioxide supply. After blowing out the water dispense valve,
leave the compressed air or carbon dioxide supply flowing. Move the control switch to
the "ICE" position to open the inlet water valve and briefly blow out the inlet water valve.
After blowing out the inlet water valve, move the control switch to the "OFF" position.
6) Close the icemaker water supply line drain valve.
7) Turn off the power supply, then remove the front panel and move the power switch to the
"OFF" position.
8) Remove the storage bin cover. Clean the storage bin liner and the storage bin cover
using a neutral cleaner. Rinse thoroughly after cleaning. Replace the storage bin cover
and the front panel in their correct positions.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
HOSHIZAKI AMERICA, INC.
618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 1A3767-010
Download from Www.Somanuals.com. All Manuals Search And Download.
|